GreenStuffWorld

Water-soluble patinas to make miniatures, scale models, terrain, and props look dirty and worn down. Water-Soluble Patina is a partially water-soluble decorative patina designed to create realistic effects of aging, grime, rust, moisture, soot, wear, and tonal variations on miniatures, models, scenery, props, and other non-porous surfaces. Its formula provides an ultra-matte, natural finish and is designed so that the pigments settle organically into crevices, textures, and reliefs, achieving more believable results than those of conventional paint. Additionally, it is a non-toxic acrylic product with no harsh fumes. It is important to shake the product well before each use, as some components may separate and settle at the bottom of the container during storage. If it has been left to stand for a long time, you can use metal balls to mix it thoroughly. Using a wet palette is not recommended. It can be applied directly or diluted slightly with water if necessary. Clean brushes and tools with water or alcohol immediately after use and prevent the product from drying on them. It can also be used with an airbrush to achieve smoother transitions, weathering effects, and large-scale aging effects. Depending on the pressure used in the compressor, it may be necessary to slightly dilute the product for use in the airbrush. In that case, add a few drops of water and stir until well diluted. Clean the airbrush as usual after use. Apply to clean, dry, grease-free surfaces such as plastic, resin, or metal. Not recommended for porous or absorbent surfaces such as untreated wood or paper. The intensity of the effect will depend on the amount applied, the number of coats, and the technique used. To remove and activate the product, use cotton swabs, a brush, or a sponge dampened with water to remove excess and activate the product, thereby achieving finishes ranging from soft and subtle to more intense, irregular, and personalized effects. Since it is partially water-soluble, the finish may be altered if it gets wet or is handled with wet hands; therefore, it is recommended to seal the final result with a matte varnish (or mod podge) to preserve it and maintain its natural appearance. Contents: 1x 60ml

Read more less

Pre-painted ruined concrete walls compatible with the Bolt Action, Warhammer 40,000, Kill Team, Necromunda, Infinity, Star Wars Legion, Marvel Crisis Protocol, and Fallout Wasteland Warfare  This set of corners and pre-painted concrete walls is designed to create urban, industrial, or post-apocalyptic scenarios on your gaming tables, providing solid cover, blocking lines of sight, and defining corridors, courtyards, and combat zones with a realistic aged concrete look. Due to their scale and use, they are ideal for miniature tabletop games or wargames where the terrain defines the tactics. Specifically, they are compatible with Bolt Action, Warhammer 40,000, Kill Team, Necromunda, Infinity, Star Wars Legion, Marvel Crisis Protocol, Fallout Wasteland Warfare, or modern role-playing games and skirmishes. Use them as perimeter walls, barricades, modular ruins, or zone dividers to add three-dimensionality and a more cinematic feel to your games. The widths of the walls are based on the inch system and the typical grid size of many boards: the shortest section measures 2.5 cm (1 inch) and the longest 7.5 cm (3 inches), allowing corners to be joined together and pieces to be easily combined to build clean and stable corners, turns, and enclosures. This set of pre-painted terrain is quick and easy to assemble, thanks to its interlocking system, with no glue required to play. However, if you prefer to fix them permanently, we recommend PVA glue; avoid cyanoacrylate if you don't want to risk damaging or whitening painted surfaces. Material: MDF woodContents: 16 fully pre-painted brick wallsHeight: 5 cmWidths: from 2.5 cm to 7.5 cm (inch system)

Read more less

Pre-painted ruined brick walls compatible with the Bolt Action, Warhammer 40,000, Kill Team, Necromunda, Infinity, Star Wars Legion, Marvel Crisis Protocol, and Fallout Wasteland Warfare  This set of corners and pre-painted brick walls is designed to create urban, industrial, or post-apocalyptic scenarios on your gaming tables, providing solid cover, blocking lines of sight, and defining corridors, courtyards, and combat zones with a realistic aged concrete look. Due to their scale and use, they are ideal for miniature tabletop games or wargames where the terrain defines the tactics. Specifically, they are compatible with Bolt Action, Warhammer 40,000, Kill Team, Necromunda, Infinity, Star Wars Legion, Marvel Crisis Protocol, Fallout Wasteland Warfare, or modern role-playing games and skirmishes. Use them as perimeter walls, barricades, modular ruins, or zone dividers to add three-dimensionality and a more cinematic feel to your games. The widths of the walls are based on the inch system and the typical grid size of many boards: the shortest section measures 2.5 cm (1 inch) and the longest 7.5 cm (3 inches), allowing corners to be joined together and pieces to be easily combined to build clean and stable corners, turns, and enclosures. This set of pre-painted terrain is quick and easy to assemble, thanks to its interlocking system, with no glue required to play. However, if you prefer to fix them permanently, we recommend PVA glue; avoid cyanoacrylate if you don't want to risk damaging or whitening painted surfaces. Material: MDF woodContents: 16 fully pre-painted brick wallsHeight: 5 cmWidths: from 2.5 cm to 7.5 cm (inch system)

Read more less

Metallic Acrylic Paint – Vivid Metal Color SeriesGSW's Vivid Metal Colors series takes metallic finishes to another level, offering extraordinarily vivid, intense colors that are hard to find in the world of model making. These almost unique shades provide a striking metallic sheen thanks to their intense colors, adding a distinctive touch to any miniature, model, or scenery piece. Formulated with the highest quality ultra-fine pigments, these pearl-based metallic paints provide a truly stunning metallic effect, guaranteeing professional results even on small or highly detailed surfaces. Their coverage, combined with fast drying, allows you to work comfortably and efficiently. They can be combined with each other or with other paints and auxiliary products such as varnishes, although it is recommended to use gloss varnish, satin varnish, or our chrome varnish. They can also be combined with our range of Candy Inks or our range of Interference or Metal Filter paints: They can be used together with candy inks, due to their high transparency and shine, acting as color filters on metallic surfaces, gems, crystals, or lights, allowing you to modify and enhance the base metallic tone without losing definition. By applying a very thin layer of ink to the already painted metal, you can achieve unique color variations—intensifying reds, greens, blues, or intermediate shades—for vibrant and deep visual effects.They can also be used in conjunction with the range of metal filters, which provide reflections that change depending on the angle of the light, generating pearly or iridescent sparkles that transform the metallic finish into something much more dynamic. This combination allows you to create striking special effects, from armor with changing sparkles to details with an almost magical appearance, producing results that stand out both on the table and in the display case.The Vivid Metal Color series is water-based and completely non-toxic, and is optimized for use with both brushes and airbrushes. For optimal performance with an airbrush, we recommend starting with a 1:1 dilution with acrylic thinner. Each bottle includes a stainless steel ball to ensure a homogeneous mixture that is ready to use in seconds. Contents: 6 x 17 ml 1x Purple Passion1x Kingsfall Gold1x Ironleaf Green1x Anvil Blue1x Flameflare Red1x Cosmic Silver

Read more less

The stackable tournament tray for miniatures from Green Stuff World is a transport and storage system designed to move miniatures neatly from game to game within a tournament, as well as between the storage area and the gaming table at home or at your club. Its design is optimized for use with magnetized miniatures, making it easy to position and move them during games, events, or tournaments. The base of this stackable tray is metalized, ensuring the figures remain secure on the surface during transport. This feature helps prevent unwanted movement when moving the Warhammer tray from one place to another and keeps the miniatures in their original arrangement without having to handle them individually each time their position is changed. This stackable tournament tray requires assembly and features thick side handles integrated into the structure itself, designed to facilitate a secure grip during manual transport and provide a more stable hold when lifting or moving the tray. We recommend using PVA glue for assembly; once assembled, the tray cannot be disassembled, enhancing its structural integrity and durability while preventing the loss of set components. Multiple transport trays can be stacked on top of one another, allowing you to organize miniatures by faction, army, project, or game system within a shelf, cabinet, or workspace. This feature also makes it easier to move several trays at once from storage to the gaming table, especially when working with multiple groups of miniatures or entire armies. The structure is made of black MDF, a material commonly used in organization and modeling accessories due to its balance between rigidity and weight. The black finish provides a uniform and discreet appearance, allowing it to blend visually with other storage elements, painting stations, or hobby furniture. The choice of this material also helps maintain a stable construction without resorting to complex components. The product is designed for easy assembly. The parts snap together quickly, allowing the transport tray to be ready for use in no time. Once assembled, the tray can be used both as a temporary stand during games and as a more permanent storage solution at home. Its design allows miniatures to remain in place and ready to be moved when necessary. These stackable Warhammer trays are used to transport miniatures between different tables during tournaments or gaming sessions, particularly Warhammer 40k tournaments, though they are especially useful in home settings, allowing entire units to be kept together on a single tray. This helps prevent individual transfers and accidents, simplifies pre-game organization, and reduces direct handling of painted miniatures. Contents: 1 tournament tray + 2 adhesive metalized rubber sheets for magnetized miniaturesUsable area: 300x420mm (11.8 x 16.53 inches)

Read more less

Candelabra with candlesSet of resin bits: Standing Candle Holders with candles. A perfect accessory to bring life to castle interiors, arcane libraries, dungeons, or gloomy taverns. Each piece has been designed with a high level of detail, accurately capturing every relief of the different candelabras, the melted candle wax, and the shapes of the flames. They are printed in high-quality 3D printing resin, which offers great definition, making it easier to highlight metallic textures or lighting effects during painting. This set includes 8 different candlestick designs to make your dioramas realistic, including pieces to illuminate castle tables, antique dining rooms, or set the scene for chaotic rituals. This product is sold unpainted and is perfect for 1:48 scales. Includes: x12 Standing Candle Holders 1:48

Read more less

Wargame trophies are awards designed to add value to any miniature or strategy game tournament. Each one consists of a high-quality ABS-like resin figure left unpainted, allowing full customization depending on the type of tournament and the theme of the event. In addition, each figure includes a square MDF base lacquered in black, with a smooth surface ideal for applying vinyls, engraved plates, or other commemorative texts. This makes every trophy a unique piece that not only recognizes the players’ efforts but also reinforces the identity and prestige of the championship. Unlike other generic awards, these trophies are created with the creative spirit of the hobby in mind. The option to paint them with metallic finishes, chrome effects, or even custom schemes inspired by each army turns them into true collector’s pieces. Whether for local leagues or large international tournaments, these trophies bring a special touch to the event, leaving players with a tangible memory of their participation and of the competitive atmosphere that defines the world of wargames. We offer 4 different models, so you can choose the one that best suits your competition. Contents: 1x resin trophy figure + Display plinth

Read more less

Bring your roleplaying scenarios to life with the dinnerware set, a collection of resin bits perfect for designing detailed scenes of great feasts, a castle dining room, remnants of a battle, taverns, and camps, among many others. It includes plates, bowls, a jug, a soup tureen, etc. This set is perfect for dioramas and thematic scenes, enriching the visual narrative with touches of everyday life. They are 3D printed with high-quality resin, so they precisely capture the shape and texture of these kitchen utensils, adding an extra level of realism to your projects, whether they are fantasy, medieval, or realistic themed. Features: Highly defined plates and kitchen utensil pieces. Made from high-quality resin, which makes them durable and ready to paint and adapt to any style (from rustic to the most refined). Includes a varied selection of plates, bowls, a jug, a soup tureen with its corresponding spoon, a salad bowl, and large plates for presenting different dishes. Compatible with 1:48/1:35 scales, the standard for wargames. Contents of the dinnerware set: Each set includes 34 pieces of a variety of plates, utensils, and serving ware for different dishes.

Read more less

Magic Effects – Ice SpellsDiscover our new collection of magic effects printed in 3D resin, specially designed to bring your miniatures, dioramas, and fantasy or science fiction scenes to life. These 3D resin bits represent a wide variety of spells and elemental powers, from bursts of fire, ice, and electricity to toxic, arcane, or supernatural effects. Each piece has been meticulously modeled to capture the dynamism of movement and the intensity of magic in full action. Their transparent design allows you to play with lighting, color, and shadows, achieving spectacular results with simple touches of paint, inks, or LED lighting effects. Take advantage of their transparency and paint these special effects with intense inks, dipping inks, or fluorescent colors. These products enhance the internal brightness of the material and allow you to achieve truly spectacular luminous transitions and energy effects. By applying thin layers of color or combining different shades, you can simulate burning fire, sparkling ice, electric shocks, or toxic fumes with unique depth and luminosity. Ideal for customizing heroes, wizards, monsters, or entire scenes, these effects are perfect for both modeling and wargamers looking to add drama and visual storytelling to their miniatures. These resin bits are made of high-quality ABS-like resin, offering strength, definition, and excellent compatibility with modeling glues and paints. Supplied unpainted, still attached to their printing sprue, and should be carefully removed before use. Perfect for wargaming miniatures from 28 to 54 mm (1:48–1:35 scale). Contents: x26

Read more less

Magic Effects – Energy WavesDiscover our new collection of magic effects printed in 3D resin, specially designed to bring your miniatures, dioramas, and fantasy or science fiction scenes to life. These 3D resin bits represent a wide variety of spells and elemental powers, from bursts of fire, ice, and electricity to toxic, arcane, or supernatural effects. Each piece has been meticulously modeled to capture the dynamism of movement and the intensity of magic in full action. Their transparent design allows you to play with lighting, color, and shadows, achieving spectacular results with simple touches of paint, inks, or LED lighting effects. Take advantage of their transparency and paint these special effects with intense inks, dipping inks, or fluorescent colors. These products enhance the internal brightness of the material and allow you to achieve truly spectacular luminous transitions and energy effects. By applying thin layers of color or combining different shades, you can simulate burning fire, sparkling ice, electric shocks, or toxic fumes with unique depth and luminosity. Ideal for customizing heroes, wizards, monsters, or entire scenes, these effects are perfect for both modeling and wargamers looking to add drama and visual storytelling to their miniatures. These resin bits are made of high-quality ABS-like resin, offering strength, definition, and excellent compatibility with modeling glues and paints. Supplied unpainted, still attached to their printing sprue, and should be carefully removed before use. Perfect for wargaming miniatures from 28 to 54 mm (1:48–1:35 scale). Contents: x8

Read more less

Magic Effects – Ice WavesDiscover our collection of magic effects printed in 3D resin, specially designed to bring your miniatures, dioramas, and fantasy or science fiction scenes to life. These 3D resin bits represent a wide variety of spells and elemental powers, from bursts of fire, ice, and electricity to toxic, arcane, or supernatural effects. Each piece has been meticulously modeled to capture the dynamism of movement and the intensity of magic in full action. Their transparent design allows you to play with lighting, color, and shadows, achieving spectacular results with simple touches of paint, inks, or LED lighting effects. Take advantage of their transparency and paint these special effects with intense inks, dipping inks, or fluorescent colors. These products enhance the internal brightness of the material and allow you to achieve truly spectacular luminous transitions and energy effects. By applying thin layers of color or combining different shades, you can simulate burning fire, sparkling ice, electric shocks, or toxic fumes with unique depth and luminosity. Ideal for customizing heroes, wizards, monsters, or entire scenes, these effects are perfect for both modeling and wargamers looking to add drama and visual storytelling to their miniatures. These resin bits are made of high-quality ABS-like resin, offering strength, definition, and excellent compatibility with modeling glues and paints. Supplied unpainted, still attached to their printing sprue, and should be carefully removed before use. Perfect for wargaming miniatures from 28 to 54 mm (1:48–1:35 scale). Contents: x8

Read more less

Pre-Painted Foldable WTC terrain | Official WTC scenery compatible with competitive Warhammer 40k tournaments WTC foldable and pre-painted WTC terrain ruins are specially designed for competitive Warhammer 40,000 games under the WTC (World Team Championship) format. This is the official scenery of the WTC circuit, developed to offer maximum functionality and a professional visual finish from the first use. These structures are the ideal choice for demanding players, tournament organizers, associations, and wargaming clubs looking for quality terrain that is quick to assemble and easy to transport. Its smart folding system allows each piece to be stored and moved comfortably, without sacrificing stability or detail. Each piece of WTC terrain or ruin has been pre-painted with professional quality and a wealth of detail, ready to use right out of the box. Or as we like to say at Green Stuff World: pre-painted by elves, with neutral tones and weathering effects that match any style of Warhammer 40k army or gaming table. These WTC format Warhammer 40k compatible folding buildings require simple initial assembly, for which we recommend the use of PVA glue. This adhesive ensures strong but flexible joints, ideal for repeated folding. We do not recommend using cyanoacrylate, as it could cause the pieces to come apart or become damaged with prolonged use. The design of each building allows for reversible assembly, so you can configure the structure in an L-shape on either the left or right, depending on your tactical needs. This offers extra versatility to customize the deployment of your scenery without the need for additional elements. In addition, the windows can be assembled open or closed, adding a tactical component to each ruin. Decide how you want to block lines of sight or control access depending on your faction's play style or the current scenario. These ruins are 100% compatible with the official WTC rules and are ideal for international events, home games, team training, or demonstrations in wargaming stores. Each WTC ruin set has been designed with durability and modularity in mind. The materials used are resistant to heavy use, and their folding system allows for easy transport without damaging the paint or compromising the structure. With this pre-painted terrain, made of MDF wood, you can raise the level of your games from the very first minute. Save assembly time, gain in aesthetics, and get ready to compete with a professional, functional, and spectacular gaming environment. Contents: 1x Pre-painted WTC Containers (Random colors, including blue, red, green, or yellow, all with the option of silver mounting.)

Read more less

Pre-Painted Foldable WTC terrain | Official WTC scenery compatible with competitive Warhammer 40k tournaments WTC foldable and pre-painted WTC terrain ruins are specially designed for competitive Warhammer 40,000 games under the WTC (World Team Championship) format. This is the official scenery of the WTC circuit, developed to offer maximum functionality and a professional visual finish from the first use. These structures are the ideal choice for demanding players, tournament organizers, associations, and wargaming clubs looking for quality terrain that is quick to assemble and easy to transport. Its smart folding system allows each piece to be stored and moved comfortably, without sacrificing stability or detail. Each piece of WTC terrain or ruin has been pre-painted with professional quality and a wealth of detail, ready to use right out of the box. Or as we like to say at Green Stuff World: pre-painted by elves, with neutral tones and weathering effects that match any style of Warhammer 40k army or gaming table. These WTC format Warhammer 40k compatible folding buildings require simple initial assembly, for which we recommend the use of PVA glue. This adhesive ensures strong but flexible joints, ideal for repeated folding. We do not recommend using cyanoacrylate, as it could cause the pieces to come apart or become damaged with prolonged use. The design of each building allows for reversible assembly, so you can configure the structure in an L-shape on either the left or right, depending on your tactical needs. This offers extra versatility to customize the deployment of your scenery without the need for additional elements. In addition, the windows can be assembled open or closed, adding a tactical component to each ruin. Decide how you want to block lines of sight or control access depending on your faction's play style or the current scenario. These ruins are 100% compatible with the official WTC rules and are ideal for international events, home games, team training, or demonstrations in wargaming stores. Each WTC ruin set has been designed with durability and modularity in mind. The materials used are resistant to heavy use, and their folding system allows for easy transport without damaging the paint or compromising the structure. With this pre-painted terrain, made of MDF wood, you can raise the level of your games from the very first minute. Save assembly time, gain in aesthetics, and get ready to compete with a professional, functional, and spectacular gaming environment. Contents: 1x Pre-Painted Foldable Two-Story WTC Terrain Ruin

Read more less

Textured Rolling Pins capable of pressing a continuous repeated pattern on clay and putties. Made of clear PMMA plastic with amazing non-stick properties. Non-toxic. They come in several different textures that you can purchase based on your specific needs. Length: 14'50 cm (5’5 inches)Diameter: 2’5cm (1 inch) USE INSTRUCTIONS:  1st - Properly mix the putty/clay until ready according to the manufacturer's recommendations. 2nd - Extend the putty/clay on a surface to be textured. For optimal results, make sure you have got a smooth and even surface before impressing with the Rolling Pins. *** We recommend using a plain Rolling Pin for this. 3rd - Depending on the type of putty/clay, it is advisable to wet the Rolling Pin to prevent any sticking. 4th - Slowly move the Rolling Pin applying equal pressure at all points for an even texture. 5th - Trim any excess putty/clay with a sharp knife. It is recommended to do this once it has dried to avoid any deformations in the putty/clay. MATERIALS: There are plenty of different putties and clays on the market and all of them can be textured using the proper technique. Usually polymer clay (Fimo or Sculpey type) are quite simple to work with these Rolling Pins as they allow for an easy correction of mistakes before they are baked. If the aim is to make textured bases, we recommend using MDF bases, because you can texture the polymer clay directly onto an MDF base, and then put it all in the oven, including the base. The cooking time of these clays are around 15 minutes at 150ºC. MDF Wood may leave a slight scent similar to that of toasted bread, but don't worry it won’t burn! In the case of epoxy putties, there are a variety of techniques which achieve similar results. Good thing is. you do not need to bake them, so they may be applied directly onto plastic bases. For Green Stuff putty, which is particularly sticky, it is required to slightly wet either the putty or the Rolling Pin with some water before texturing. You may also reduce the stickiness by applying talcum powder, or using Sculptor Vaseline (LINK). Other epoxy putties like the Milliput putty, for example, are also suitable, but we wouldn't recommend to wet them much since it will hinder your work. Furthermore, if the mixture is too sticky, it is better to continue kneading until the stickiness is gone. *** For this type of epoxy putties, it is very important to clean the rolling pins properly after use. CARE INSTRUCTIONS: After working with the Rolling Pins, use a Scratch Brush (LINK) and plenty of water to clean off any residue on the Rolling Pins if required. SAFETY: To ensure safety, children should be closely monitored by a responsible adult. 

Read more less

Flexible sanding blocks are versatile tools, ideal for modelling, crafts, and cosplay. Made from 5 mm EVA foam, they provide a comfortable surface that easily conforms to hand curves and irregular areas. Their 100x80 mm size makes them easy to handle and suitable for both fine detail work and larger surfaces. Each Flexible Sanding Pad is coated with abrasive on one side only, allowing for more precise control without damaging the back. They come in various colours that indicate the grit level, making them easy to identify while working. They can be cut with scissors to adapt to specific shapes or angles. These blocks combine comfort, precision, and flexibility, making them essential for surface preparation and finishing work. Size: 100x80 mmGrit: #2000Contents: 5x

Read more less

Rigid sanding pads are strong and precise tools, ideal for modelling, crafts, and cosplay. They are made of 5 mm thick rigid PVC foam, which provides a firm and durable base. They retain the same practical 100x80 mm dimensions as the flexible models but offer a more stable structure. Unlike flexible sanding blocks, these blocks feature wet sandpaper on both sides, enabling dual-sided use and extended durability. Their rigid construction allows them to lie completely flat on the work surface, making it easier to sand large parts directly on the table. They cannot be cut with scissors, but they offer greater control on flat surfaces or when even pressure is needed. They are the perfect choice for those seeking precision and stability in finishing work. Size: 100x80 mmGrit: #2500Contents: 5x

Read more less

Professional high-quality wet sandpaper for modeling, craft, DIY, and restoration works. These wet sandpapers have been impregnated with a synthetic abrasive on a waterproof base for wet sanding hand-works. Moisten the sandpaper with water or other lubricant and work on a wet surface, so it will prevent the surface from getting rough. For a perfect sanding/polishing of your models and miniatures, and combine different numbers progressively progressing from thickest grains (lower numbers) to finer grains (higher numbers), achieving an extraordinarily smooth and even finish. Easy to cut with scissors to use in different sizes, and also to adapt to other sanding tools.

Read more less

Professional high-quality wet sandpaper for modeling, craft, DIY, and restoration works. These wet sandpapers have been impregnated with a synthetic abrasive on a waterproof base for wet sanding hand-works. Moisten the sandpaper with water or other lubricant and work on a wet surface, so it will prevent the surface from getting rough. For a perfect sanding/polishing of your models and miniatures, and combine different numbers progressively progressing from thickest grains (lower numbers) to finer grains (higher numbers), achieving an extraordinarily smooth and even finish. Easy to cut with scissors to use in different sizes, and also to adapt to other sanding tools.

Read more less

The Green Stuff World hand sandpaper holder or hand sanding block is a sturdy yet lightweight tool, 3D printed in high-strength PLA, and offers the ultimate solution for achieving flawless surfaces in scale modeling, wargaming, dioramas, and cosplay. Its ergonomic design provides a comfortable and precise grip, allowing for both rough sanding and fine polishing on miniatures, 3D-printed parts, or EVA foam armor. Available in two versions — flat and curved — the holder adapts to any geometry: straight vehicle edges, organic scenic-base contours, or pronounced curves on helmets and pauldrons. The internal clamp keeps wet- or dry-sandpaper sheets perfectly taut and wrinkle-free, whatever the grit thickness. Its width matches exactly half a sheet of Green Stuff World’s standard sandpaper, maximising the use of every sheet; nevertheless, it can be used with paper from any other brand, making it a versatile, indispensable addition to your workbench. Dimensions: 45 mm wideSurface: CurvedContents: 1 ×

Read more less

Resin street signs 3D printed scenery set for your favorite wargame, which could be a fantastic addition to the scenery and terrains of your tabletop games. Made with 3D printing technology for high-quality and realistic details, enhancing your gaming experience. This item includes 20x plasticard profiles, 2.5 mm wide and 50 mm, for holding road signs. By adding these ABS-like resin bits to your board games, you add a realistic touch to your games. It has been carefully designed to mimic classic elements present in many modern cities, but in miniature. Some elements in this category may require modeling glue and other modeling tools to assemble or integrate them into your game tables. This product comes unpainted and is perfect for 1:48 miniatures. Scale: 1:48Content: 18x 

Read more less

Printed Metal Litter Bins (pack x 4) 3D printed scenery set for your favorite wargame, which could be a fantastic addition to the scenery and terrains of your tabletop games. Made in 3D printing with high quality and very realistic details, which will enhance your gaming experience. By adding these ABS-like resin bits to your board games, you add a realistic touch to your games. It has been carefully designed to mimic classic elements present in many modern cities but in miniature. Some elements in this category may require modeling glue and other modeling tools to assemble or integrate them into your game tables. This product comes unpainted and is perfect for 28-35 mm (1:58 - 1:48) miniatures. Size: 13x20x13mm - 16x23x14mmScale: 1:58 - 1:48Content: 4x

Read more less

Printed Mailboxes (pack x14) 3D printed scenery set for your favorite wargame, which could be a fantastic addition to the scenery and terrains of your tabletop games. Made in 3D printing with high quality and very realistic details, which will enhance your gaming experience. By adding these ABS-like resin bits to your board games, you add a realistic touch to your games. It has been carefully designed to mimic classic elements present in many modern cities but in miniature. Some elements in this category may require modeling glue and other modeling tools to assemble or integrate them into your game tables. This product comes unpainted and is perfect for 28-35 mm (1:58 - 1:48) miniatures. Size: 8x10x3mm - 12x23x12mmScale: 1:58 - 1:48Content: 14x

Read more less

Shopping Carts (pack x2) 3D printed scenery set for your favorite wargame, which could be a fantastic addition to the scenery and terrains of your tabletop games. Made in 3D printing with high quality and very realistic details, which will enhance your gaming experience. By adding these ABS-like resin bits to your board games, you add a realistic touch to your games. It has been carefully designed to mimic classic elements present in many modern cities but in miniature. Some elements in this category may require modeling glue and other modeling tools to assemble or integrate them into your game tables. This product comes unpainted and is perfect for 28-35 mm (1:58 - 1:48) miniatures. Size: 40x35x30mmScale: 1:58 - 1:48Content: 2x Shopping Carts

Read more less

Waiting Park Benches (pack x2) 3D printed scenery set for your favorite wargame, which could be a fantastic addition to the scenery and terrains of your tabletop games. Made in 3D printing with high quality and very realistic details, which will enhance your gaming experience. By adding these ABS-like resin bits to your board games, you add a realistic touch to your games. It has been carefully designed to mimic classic elements present in many modern cities but in miniature. Some elements in this category may require modeling glue and other modeling tools to assemble or integrate them into your game tables. This product comes unpainted and is perfect for 28-35 mm (1:58 - 1:48) miniatures. Size: 45x25x24mmScale: 1:58 - 1:48Content: 2x

Read more less

Waiting Church Benches (pack x2) 3D printed scenery set for your favorite wargame, which could be a fantastic addition to the scenery and terrains of your tabletop games. Made in 3D printing with high quality and very realistic details, which will enhance your gaming experience. By adding these ABS-like resin bits to your board games, you add a realistic touch to your games. It has been carefully designed to mimic classic elements present in many modern cities but in miniature. Some elements in this category may require modeling glue and other modeling tools to assemble or integrate them into your game tables. This product comes unpainted and is perfect for 28-35 mm (1:58 - 1:48) miniatures. Size: 54 x 24 x 30mmScale: 1:58 - 1:48Content: 2x

Read more less

Stunning range of printed miniature stained glass, designed to bring vibrant and authentic touches to miniature scenes, dollhouses, dioramas, and scale models. Our printed miniature stained glass captures the essence of traditional stained glass with intricate designs and vivid colors, meticulously crafted to fit small-scale environments. These products are crafted using high-quality transparent plastic sheets, which serve as the perfect canvas for detailed and vibrant designs, ensuring each piece boasts sharp, clear patterns and brilliant colors that mimic the beauty and intricacy of full-sized stained glass windows. The main feature of Green Stuff World’s miniature stained glass is our innovative double-printing system. This unique method ensures that the designs remain visible and striking, even without backlighting. Whether your model is displayed in a well-lit area or a darker setting, it retains its beauty and clarity. This double printing system also makes our product ideal for use on black backgrounds, where traditional transparent stained glass effects might be lost. This innovation ensures that even in less-than-ideal lighting conditions, its visual impact enhances the overall aesthetic of your project. The interplay of light and color through them creates a dynamic and captivating visual effect, adding depth and realism to projects. Whether you’re a hobbyist, model builder, or collector, our miniature stained glass enhances the aesthetic quality of your work, providing a professional and polished look. Enhance your creations with a stunning and realistic touch using also our exclusive miniature windows collection, available only at Green Stuff World. For assembly, we recommend using PVA glue or cyanoacrylate glue. Thickness: 0.3 mmSize: 150x220 mmScale: 1/48 - 1/35Content: 1 set

Read more less

Miniature Windows - Classic Arched - Large Miniature window frames are meticulously crafted, scaled-down versions of real windows designed for integration into modern and fantasy dioramas as well as dollhouses. These frames play a crucial role in enhancing the realism and intricate detail of dioramas, defining the architectural style and period of the houses.  They can be installed in prefabricated or custom-made houses using clear-drying adhesives. Essential tools for painting, creating, and installing these frames include sharp cutting blades, tweezers, and fine-tipped brushes. Miniature window frames are essential for bringing small worlds to life, whether for a charming dollhouse or a detailed diorama. Enhance the finish using them with our miniature stained glass collection, available exclusively at Green Stuff World, for a stunning and realistic touch to your creations. We recommend using PVA glue or cyanoacrylate glue for assembly and model paints for painting, as these frames are delivered unpainted. Thickness: 2 mmSize: 150x220 mmContent: Each set includes 2 parts (Part A + Part B) that can be used together for greater detail and depth, or they can be used separately. 

Read more less

Give your army a heavenly and mystical touch with our exclusive collection of 40K Cherub Angels, 3D printed resin bits. These detailed 40k Cherubs figures will transform your miniatures, miniature bases, and scenarios into true masterpieces, bringing a divine and dark gothic grimdark air to your games. Our online store specializes in offering sets of mechanical, diabolical angels, and other small flying minions, designed to be compatible with a variety of fantasy miniature games such as 9th Age, ASOIAF, WHF, Warhammer 40K, and the reborn WH the Old World. Made from ABS-like high-quality resin for 3D printers, these bits stand out for their exceptional level of detail, perfect for a fantasy aesthetic in a dark science fiction universe that fits perfectly into the grimdark aesthetic. From small Angel Cherubs with scrolls to winged figures with sensors and relics, each piece is designed to be compatible with your 1:48 miniatures, offering you the possibility to customize and give a unique look to your figures and squads. Whether you are an enthusiastic modeler or a wargamer, these Warhammer bits that are compatible will allow you to enrich your conversions and make your heroes or special units stand out on the battlefield. These cherubims are delivered unpainted and in their printing matrix, with easy-to-remove stands so you can assemble them without complications and adapt them to your army. For precise assembly, in our store, you will find essential modeling tools such as modeling glue, specialized model paints, and ultra-flat precision modeling pliers, ideal for working with resin and ensuring clean and professional assemblies. Contents: 4x

Read more less

Neoprene Terrain set compatible with all fantasy wargames Highest quality 2D terrain on the market. Constructed from neoprene exactly to the specifications to be compatible with Warhammer but can be used in all kind of fantasy wargames to use on your table directly or on a battle mat. These 22 durable pieces of terrain will take your epic battles to a whole new level. Light and easy to store and transport, you will always have a great battlefield ready to use. The terrain pieces are anti-slip and resistant to wrinkles and creases. This 2D Terrain Set comes with: 3pcs Hills - size: 6x8”3pcs Forests - size: 6x10"2pcs Fields - size: 6x8”6pcs Walls - size: 1x8”2pcs Water / Lakes - size: 6x10”2pcs Ruins - size: 8x8”2pcs Buildings - size: 6x8”2pcs Rocks - size: 6x6” TOTAL 22

Read more less

Acrylic starter kit for Painting Fantasy miniatures from Green Stuff World This is a Maxx Formula Acrylic Paint Set specifically formulated for use in painting models, miniatures, and dioramas. It includes a range of highly pigmented acrylic colors perfect for hobbyists who want to take their projects to the next level and achieve professional-looking results. The Maxx Formula Hobby Sets by Green Stuff World is an exceptional product that offers high-quality paints in a range of vibrant colors. These acrylic paints are highly pigmented and offer a high-coverage and smooth matte finish. They are made using new-generation pigments that have been specially selected by experienced artists to provide hobbyists with the highest quality acrylics possible. One of the key features of these acrylics is the use of dropper bottles. These bottles are designed for easy and precise dispensing of the paint and a controlled flow of paint. They are perfect for hobbyists who need to apply the paint exactly where they need it, without wasting any. The dropper bottles also include a metal ball that helps the mixing thoroughly and ensures even distribution throughout the bottle. This feature is particularly useful for hobbyists who may not use them regularly, as it prevents the pigment from settling at the bottom of the bottle over time. Additionally, the dropper bottle has a tight-fitting cap that seals the bottle tightly, preventing air from entering and drying out the paint. This helps to ensure that the colors remain fresh and usable for a long time, even if it is not used frequently. These are versatile colors that can be used with both brush and airbrush techniques. Hobbyists can also use these paints with an airbrush when slightly diluted with Acrylic Thinner, allowing them to achieve a range of effects that would otherwise be difficult to achieve. This versatility makes the range ideal for those who want to experiment with different painting techniques and achieve different effects. Whether you're a beginner or an experienced hobbyist, the Maxx Formula Hobby Set can help you take your projects to the next level. This product is water-based, non-toxic, and does not contain latex. Before use, be sure to shake the container well. It also comes with a stainless steel mixing ball to ensure even distribution of the paint.  Contains 8x 17ml. 1 x Hellfire Red 1 x Dwarven Flesh 1 x Bestial Brown 1 x Ivory Tusk 1 x Rocket Green 1 x Quicksilver 1 x Elder Bronze 1 x El Dorado

Read more less

Model grass strips are an innovative solution for the creation of detailed and realistic landscapes in miniature, diorama, and scenery projects. These self-adhesive tuft strips greatly simplify the process of decorating large surfaces: you just need to carefully remove the grass strips using tweezers or your fingers and adhere them to the desired surface. They can be used as they are or cut into smaller sizes.  Although their built-in adhesive provides a firm initial hold, it is recommended to apply a small amount of modeling glue to uneven surfaces to ensure optimal and long-lasting adhesion. They are designed with high-quality materials, ensuring a natural and durable look to your creations. Their density and texture provide amazing realism, making them ideal for adding an authentic touch of nature to your landscapes. For even more realism, combine them with our static grass, grass tufts, basing materials, and textured paints. Fiber Size: 12 mm high  Length: 6 cm Sheet size: 7x14 cm Content: 12

Read more less

Model grass strips are an innovative solution for the creation of detailed and realistic landscapes in miniature, diorama, and scenery projects. These self-adhesive tuft strips greatly simplify the process of decorating large surfaces: you just need to carefully remove the grass strips using tweezers or your fingers and adhere them to the desired surface. They can be used as they are or cut into smaller sizes.  Although their built-in adhesive provides a firm initial hold, it is recommended to apply a small amount of modeling glue to uneven surfaces to ensure optimal and long-lasting adhesion. They are designed with high-quality materials, ensuring a natural and durable look to your creations. Their density and texture provide amazing realism, making them ideal for adding an authentic touch of nature to your landscapes. For even more realism, combine them with our static grass, grass tufts, basing materials, and textured paints. Fiber Size: 12 mm high  Length: 6 cm Sheet size: 7x14 cm Content: 12

Read more less

Hobby sand is an indispensable material on any modeler's table or workshop as it is ideal for building realistic terrain in dioramas, decorating miniature bases for wargames, and many other creative hobbies. Made of an easy-to-glue and paint material, it is also available in a wide range of colors and sizes, allowing you to choose the most suitable option for each project. When applied to the base or floor of a model, it imitates the natural textures and characteristics of real landscapes, providing a high level of detail and authenticity. It is recommended to apply with PVA glue, tuft glue, or cyanoacrylate glue. Contains: 200 ml (approximate weight 100gr) Size of grain: Approx. 2-5mmColor: NaturalContains: 200ml (approximate weight 100gr)

Read more less

Hobby Sand Sand used for bases and modeling made out of the gravel. It is recommended to apply with either white glue or cyanoacrylate glue. Size of grain: Approx. 1-3mmColour: FieldContains: 200ml Hobbyzand Zand dat gebruikt kan worden voor bases en modelbouw. Gemaakt uit gravel. Gebruik dit zand op een onderlaag die ingesmeerd is met PVA, witte lijm of secondenlijm. Uitschudden of met de vinger verdelen. Korrelgrootte is 1-3mm (grof) Veldkleur Verpakking is pot met draaideksel Inhoud 200ml (ong 100gr)

Read more less

Dwarf Resin bits are compatible with games such as Warhammer: The Old World and any dwarf army. This set of resin products created by Green Stuff World has been specially designed to be compatible with games such as Warhammer: The Old World and more specifically the dwarf army. 3D resin printing offers a fascinating addition to your arsenal of wargaming and hobby tools. With this technology, you can create custom scenery, miniatures, and accessories with exceptional detail, enhancing your gaming experience. Bring a realistic touch to your bases, dioramas, and figures using these high-quality, ABS-like plastic bits. Carefully designed to replicate real species, these are available in various shapes and sizes to suit all needs and scales. Selecting the right model glue and modeling tools is essential to assembling your Warhammer bits effectively and achieving optimum results. Understanding the project requirements, exploring the available options, and assessing their performance and suitability are key factors. In addition, taking into account available experience and resources, keeping abreast of the latest developments, seeking expert advice, and considering long-term maintenance are crucial to making informed decisions. These products are supplied unpainted and are ideal for 28-35-54mm miniatures (1:48 - 1:35 scale). Each set includes 20x Dwarf Pistols

Read more less

Textured Rolling Pins capable of pressing a continuous repeated pattern on clay and putties. Made of clear PMMA plastic with amazing non-stick properties. Non-toxic. They come in several different textures that you can purchase based on your specific needs. Length: 14'50 cm (5’5 inches)Diameter: 2’5cm (1 inch) USE INSTRUCTIONS:  1st - Properly mix the putty/clay until ready according to the manufacturer's recommendations. 2nd - Extend the putty/clay on a surface to be textured. For optimal results, make sure you have got a smooth and even surface before impressing with the Rolling Pins. *** We recommend using a plain Rolling Pin for this. 3rd - Depending on the type of putty/clay, it is advisable to wet the Rolling Pin to prevent any sticking. 4th - Slowly move the Rolling Pin applying equal pressure at all points for an even texture. 5th - Trim any excess putty/clay with a sharp knife. It is recommended to do this once it has dried to avoid any deformations in the putty/clay. MATERIALS: There are plenty of different putties and clays on the market and all of them can be textured using the proper technique. Usually polymer clay (Fimo or Sculpey type) are quite simple to work with these Rolling Pins as they allow for an easy correction of mistakes before they are baked. If the aim is to make textured bases, we recommend using MDF bases, because you can texture the polymer clay directly onto an MDF base, and then put it all in the oven, including the base. The cooking time of these clays are around 15 minutes at 150ºC. MDF Wood may leave a slight scent similar to that of toasted bread, but don't worry it won’t burn! In the case of epoxy putties, there are a variety of techniques which achieve similar results. Good thing is. you do not need to bake them, so they may be applied directly onto plastic bases. For Green Stuff putty, which is particularly sticky, it is required to slightly wet either the putty or the Rolling Pin with some water before texturing. You may also reduce the stickiness by applying talcum powder, or using (Sculptor) Vaseline. Other epoxy putties like the Milliput putty, for example, are also suitable, but we wouldn't recommend to wet them much since it will hinder your work. Furthermore, if the mixture is too sticky, it is better to continue kneading until the stickiness is gone. *** For this type of epoxy putties, it is very important to clean the rolling pins properly after use. CARE INSTRUCTIONS: After working with the Rolling Pins, use a Scratch Brush and plenty of water to clean off any residue on the Rolling Pins if required. SAFETY: To ensure safety, children should be closely monitored by a responsible adult.  

Read more less