46x Resin Oil Cans 3D printed
A plate containing 46 high quality resin printed oil cans. They come in various different sizes and types for a broader range of choice between styles. Also suitable as gasoline, gas and oil cannisters.
This product comes unpainted and it is perfect for 32-54 mm miniatures (1:48, 1:35).
Each set contains 46x Resin Oil Cans.
Paint Set - CHROME
Alcohol-based metallic paints allow for achieving an effect that imitates the metallic reflection of a mirror-like chrome surface.
Although it is designed to be used with a brush, it also allows its application with an airbrush, it can be applied on any surface regardless of color, and should always be cleaned with alcohol.
The drying time that can vary depending on the environmental conditions and the thickness of the applied layer, but generally can range between 5 and 30 minutes, so it is recommended to protect the surface during its drying.
The mirror effect could be reduced or even lost if inks or varnishes are added on top.
This paint, when fresh, has the ability to dissolve the same paint already dried underneath, so it is recommended to apply it in a single pass, and on not too-large surfaces.
Contains: 6x chrome paint pots
Textured Rolling Pins capable of pressing a continuous repeated pattern on clay and putties. Made of clear PMMA plastic with amazing non-stick properties. Non-toxic. They come in several different textures that you can purchase based on your specific needs.
Length: 14'50 cm (5’5 inches)Diameter: 2’5cm (1 inch)
USE INSTRUCTIONS:
1st - Properly mix the putty/clay until ready according to the manufacturer's recommendations.
2nd - Extend the putty/clay on a surface to be textured. For optimal results, make sure you have got a smooth and even surface before impressing with the Rolling Pins. *** We recommend using a plain Rolling Pin for this.
3rd - Depending on the type of putty/clay, it is advisable to wet the Rolling Pin to prevent any sticking.
4th - Slowly move the Rolling Pin applying equal pressure at all points for an even texture.
5th - Trim any excess putty/clay with a sharp knife. It is recommended to do this once it has dried to avoid any deformations in the putty/clay.
MATERIALS:
There are plenty of different putties and clays on the market and all of them can be textured using the proper technique.
Usually polymer clay (Fimo or Sculpey type) are quite simple to work with these Rolling Pins as they allow for an easy correction of mistakes before they are baked. If the aim is to make textured bases, we recommend using MDF bases, because you can texture the polymer clay directly onto an MDF base, and then put it all in the oven, including the base. The cooking time of these clays are around 15 minutes at 150ºC. MDF Wood may leave a slight scent similar to that of toasted bread, but don't worry it won’t burn!
In the case of epoxy putties, there are a variety of techniques which achieve similar results. Good thing is. you do not need to bake them, so they may be applied directly onto plastic bases.
For Green Stuff putty, which is particularly sticky, it is required to slightly wet either the putty or the Rolling Pin with some water before texturing. You may also reduce the stickiness by applying talcum powder, or using (Sculptor) Vaseline.
Other epoxy putties like the Milliput putty, for example, are also suitable, but we wouldn't recommend to wet them much since it will hinder your work. Furthermore, if the mixture is too sticky, it is better to continue kneading until the stickiness is gone.
*** For this type of epoxy putties, it is very important to clean the rolling pins properly after use.
CARE INSTRUCTIONS:
After working with the Rolling Pins, use a Scratch Brush and plenty of water to clean off any residue on the Rolling Pins if required.
SAFETY:
To ensure safety, children should be closely monitored by a responsible adult.
Textured Rolling Pins capable of pressing a continuous repeated pattern on clay and putties. Made of clear PMMA plastic with amazing non-stick properties. Non-toxic. They come in several different textures that you can purchase based on your specific needs.
Length: 14'50 cm (5’5 inches)Diameter: 2’5cm (1 inch)
USE INSTRUCTIONS:
1st - Properly mix the putty/clay until ready according to the manufacturer's recommendations.
2nd - Extend the putty/clay on a surface to be textured. For optimal results, make sure you have got a smooth and even surface before impressing with the Rolling Pins. *** We recommend using a plain Rolling Pin for this.
3rd - Depending on the type of putty/clay, it is advisable to wet the Rolling Pin to prevent any sticking.
4th - Slowly move the Rolling Pin applying equal pressure at all points for an even texture.
5th - Trim any excess putty/clay with a sharp knife. It is recommended to do this once it has dried to avoid any deformations in the putty/clay.
MATERIALS:
There are plenty of different putties and clays on the market and all of them can be textured using the proper technique.
Usually polymer clay (Fimo or Sculpey type) are quite simple to work with these Rolling Pins as they allow for an easy correction of mistakes before they are baked. If the aim is to make textured bases, we recommend using MDF bases, because you can texture the polymer clay directly onto an MDF base, and then put it all in the oven, including the base. The cooking time of these clays are around 15 minutes at 150ºC. MDF Wood may leave a slight scent similar to that of toasted bread, but don't worry it won’t burn!
In the case of epoxy putties, there are a variety of techniques which achieve similar results. Good thing is. you do not need to bake them, so they may be applied directly onto plastic bases.
For Green Stuff putty, which is particularly sticky, it is required to slightly wet either the putty or the Rolling Pin with some water before texturing. You may also reduce the stickiness by applying talcum powder, or using (Sculptor) Vaseline.
Other epoxy putties like the Milliput putty, for example, are also suitable, but we wouldn't recommend to wet them much since it will hinder your work. Furthermore, if the mixture is too sticky, it is better to continue kneading until the stickiness is gone.
*** For this type of epoxy putties, it is very important to clean the rolling pins properly after use.
CARE INSTRUCTIONS:
After working with the Rolling Pins, use a Scratch Brush and plenty of water to clean off any residue on the Rolling Pins if required.
SAFETY:
To ensure safety, children should be closely monitored by a responsible adult.
Textured Rolling Pins capable of pressing a continuous repeated pattern on clay and putties. Made of clear PMMA plastic with amazing non-stick properties. Non-toxic. They come in several different textures that you can purchase based on your specific needs.
Length: 14'50 cm (5’5 inches)Diameter: 2’5cm (1 inch)
USE INSTRUCTIONS:
1st - Properly mix the putty/clay until ready according to the manufacturer's recommendations.
2nd - Extend the putty/clay on a surface to be textured. For optimal results, make sure you have got a smooth and even surface before impressing with the Rolling Pins. *** We recommend using a plain Rolling Pin for this.
3rd - Depending on the type of putty/clay, it is advisable to wet the Rolling Pin to prevent any sticking.
4th - Slowly move the Rolling Pin applying equal pressure at all points for an even texture.
5th - Trim any excess putty/clay with a sharp knife. It is recommended to do this once it has dried to avoid any deformations in the putty/clay.
MATERIALS:
There are plenty of different putties and clays on the market and all of them can be textured using the proper technique.
Usually polymer clay (Fimo or Sculpey type) are quite simple to work with these Rolling Pins as they allow for an easy correction of mistakes before they are baked. If the aim is to make textured bases, we recommend using MDF bases, because you can texture the polymer clay directly onto an MDF base, and then put it all in the oven, including the base. The cooking time of these clays are around 15 minutes at 150ºC. MDF Wood may leave a slight scent similar to that of toasted bread, but don't worry it won’t burn!
In the case of epoxy putties, there are a variety of techniques which achieve similar results. Good thing is. you do not need to bake them, so they may be applied directly onto plastic bases.
For Green Stuff putty, which is particularly sticky, it is required to slightly wet either the putty or the Rolling Pin with some water before texturing. You may also reduce the stickiness by applying talcum powder, or using (Sculptor) Vaseline.
Other epoxy putties like the Milliput putty, for example, are also suitable, but we wouldn't recommend to wet them much since it will hinder your work. Furthermore, if the mixture is too sticky, it is better to continue kneading until the stickiness is gone.
*** For this type of epoxy putties, it is very important to clean the rolling pins properly after use.
CARE INSTRUCTIONS:
After working with the Rolling Pins, use a Scratch Brush and plenty of water to clean off any residue on the Rolling Pins if required.
SAFETY:
To ensure safety, children should be closely monitored by a responsible adult.
Textured Rolling Pins capable of pressing a continuous repeated pattern on clay and putties. Made of clear PMMA plastic with amazing non-stick properties. Non-toxic. They come in several different textures that you can purchase based on your specific needs.
Length: 14'50 cm (5’5 inches)Diameter: 2’5cm (1 inch)
USE INSTRUCTIONS:
1st - Properly mix the putty/clay until ready according to the manufacturer's recommendations.
2nd - Extend the putty/clay on a surface to be textured. For optimal results, make sure you have got a smooth and even surface before impressing with the Rolling Pins. *** We recommend using a plain Rolling Pin for this.
3rd - Depending on the type of putty/clay, it is advisable to wet the Rolling Pin to prevent any sticking.
4th - Slowly move the Rolling Pin applying equal pressure at all points for an even texture.
5th - Trim any excess putty/clay with a sharp knife. It is recommended to do this once it has dried to avoid any deformations in the putty/clay.
MATERIALS:
There are plenty of different putties and clays on the market and all of them can be textured using the proper technique.
Usually polymer clay (Fimo or Sculpey type) are quite simple to work with these Rolling Pins as they allow for an easy correction of mistakes before they are baked. If the aim is to make textured bases, we recommend using MDF bases, because you can texture the polymer clay directly onto an MDF base, and then put it all in the oven, including the base. The cooking time of these clays are around 15 minutes at 150ºC. MDF Wood may leave a slight scent similar to that of toasted bread, but don't worry it won’t burn!
In the case of epoxy putties, there are a variety of techniques which achieve similar results. Good thing is. you do not need to bake them, so they may be applied directly onto plastic bases.
For Green Stuff putty, which is particularly sticky, it is required to slightly wet either the putty or the Rolling Pin with some water before texturing. You may also reduce the stickiness by applying talcum powder, or using (Sculptor) Vaseline.
Other epoxy putties like the Milliput putty, for example, are also suitable, but we wouldn't recommend to wet them much since it will hinder your work. Furthermore, if the mixture is too sticky, it is better to continue kneading until the stickiness is gone.
*** For this type of epoxy putties, it is very important to clean the rolling pins properly after use.
CARE INSTRUCTIONS:
After working with the Rolling Pins, use a Scratch Brush and plenty of water to clean off any residue on the Rolling Pins if required.
SAFETY:
To ensure safety, children should be closely monitored by a responsible adult.
Textured Rolling Pins capable of pressing a continuous repeated pattern on clay and putties. Made of clear PMMA plastic with amazing non-stick properties. Non-toxic. They come in several different textures that you can purchase based on your specific needs.
Length: 14'50 cm (5’5 inches)Diameter: 2’5cm (1 inch)
USE INSTRUCTIONS:
1st - Properly mix the putty/clay until ready according to the manufacturer's recommendations.
2nd - Extend the putty/clay on a surface to be textured. For optimal results, make sure you have got a smooth and even surface before impressing with the Rolling Pins. *** We recommend using a plain Rolling Pin for this.
3rd - Depending on the type of putty/clay, it is advisable to wet the Rolling Pin to prevent any sticking.
4th - Slowly move the Rolling Pin applying equal pressure at all points for an even texture.
5th - Trim any excess putty/clay with a sharp knife. It is recommended to do this once it has dried to avoid any deformations in the putty/clay.
MATERIALS:
There are plenty of different putties and clays on the market and all of them can be textured using the proper technique.
Usually polymer clay (Fimo or Sculpey type) are quite simple to work with these Rolling Pins as they allow for an easy correction of mistakes before they are baked. If the aim is to make textured bases, we recommend using MDF bases, because you can texture the polymer clay directly onto an MDF base, and then put it all in the oven, including the base. The cooking time of these clays are around 15 minutes at 150ºC. MDF Wood may leave a slight scent similar to that of toasted bread, but don't worry it won’t burn!
In the case of epoxy putties, there are a variety of techniques which achieve similar results. Good thing is. you do not need to bake them, so they may be applied directly onto plastic bases.
For Green Stuff putty, which is particularly sticky, it is required to slightly wet either the putty or the Rolling Pin with some water before texturing. You may also reduce the stickiness by applying talcum powder, or using (Sculptor) Vaseline.
Other epoxy putties like the Milliput putty, for example, are also suitable, but we wouldn't recommend to wet them much since it will hinder your work. Furthermore, if the mixture is too sticky, it is better to continue kneading until the stickiness is gone.
*** For this type of epoxy putties, it is very important to clean the rolling pins properly after use.
CARE INSTRUCTIONS:
After working with the Rolling Pins, use a Scratch Brush and plenty of water to clean off any residue on the Rolling Pins if required.
SAFETY:
To ensure safety, children should be closely monitored by a responsible adult.
Textured Rolling Pins capable of pressing a continuous repeated pattern on clay and putties. Made of clear PMMA plastic with amazing non-stick properties. Non-toxic. They come in several different textures that you can purchase based on your specific needs.
Length: 14'50 cm (5’5 inches)Diameter: 2’5cm (1 inch)
USE INSTRUCTIONS:
1st - Properly mix the putty/clay until ready according to the manufacturer's recommendations.
2nd - Extend the putty/clay on a surface to be textured. For optimal results, make sure you have got a smooth and even surface before impressing with the Rolling Pins. *** We recommend using a plain Rolling Pin for this.
3rd - Depending on the type of putty/clay, it is advisable to wet the Rolling Pin to prevent any sticking.
4th - Slowly move the Rolling Pin applying equal pressure at all points for an even texture.
5th - Trim any excess putty/clay with a sharp knife. It is recommended to do this once it has dried to avoid any deformations in the putty/clay.
MATERIALS:
There are plenty of different putties and clays on the market and all of them can be textured using the proper technique.
Usually polymer clay (Fimo or Sculpey type) are quite simple to work with these Rolling Pins as they allow for an easy correction of mistakes before they are baked. If the aim is to make textured bases, we recommend using MDF bases, because you can texture the polymer clay directly onto an MDF base, and then put it all in the oven, including the base. The cooking time of these clays are around 15 minutes at 150ºC. MDF Wood may leave a slight scent similar to that of toasted bread, but don't worry it won’t burn!
In the case of epoxy putties, there are a variety of techniques which achieve similar results. Good thing is. you do not need to bake them, so they may be applied directly onto plastic bases.
For Green Stuff putty, which is particularly sticky, it is required to slightly wet either the putty or the Rolling Pin with some water before texturing. You may also reduce the stickiness by applying talcum powder, or using (Sculptor) Vaseline.
Other epoxy putties like the Milliput putty, for example, are also suitable, but we wouldn't recommend to wet them much since it will hinder your work. Furthermore, if the mixture is too sticky, it is better to continue kneading until the stickiness is gone.
*** For this type of epoxy putties, it is very important to clean the rolling pins properly after use.
CARE INSTRUCTIONS:
After working with the Rolling Pins, use a Scratch Brush and plenty of water to clean off any residue on the Rolling Pins if required.
SAFETY:
To ensure safety, children should be closely monitored by a responsible adult.
Plastic Barricades | Steel Barricades printed in 3D for miniatures and Wargames
3D printed scenery set for your favorite wargame, which could be a fantastic addition to the scenery and terrains of your tabletop games. Made in 3D printing with high quality and very realistic details, which will enhance your gaming experience.
By adding these ABS-like resin bits to your board games you add a realistic touch to your games. It has been carefully designed to mimic classic elements present in many modern cities but in miniature.
Some elements in this category may require modeling glue and other modeling tools to assemble or integrate them into your game tables. This product comes unpainted and is perfect for 28-35 mm (1:58 - 1:48) miniatures.
Size: (3x) 60x30mm and (1x) 50x30mmScale: 1:58 - 1:48Content: 4x
Notice: Large, flat printed resin parts may suffer some small curvature if exposed to high temperatures, e.g. during transport. In case of receiving a part with such a small curvature, it can be straightened again by applying a little heat with a hair dryer.
Metal Barricades | Steel Barricades printed in 3D for miniatures and Wargames
3D printed scenery set for your favorite wargame, which could be a fantastic addition to the scenery and terrains of your tabletop games. Made in 3D printing with high quality and very realistic details, which will enhance your gaming experience.
By adding these ABS-like resin bits to your board games you add a realistic touch to your games. It has been carefully designed to mimic classic elements present in many modern cities but in miniature.
Some elements in this category may require modeling glue and other modeling tools to assemble or integrate them into your game tables. This product comes unpainted and is perfect for 28-35 mm (1:58 - 1:48) miniatures.
Size: (3x) 60x30mm and (1x) 50x30mmScale: 1:58 - 1:48Content: 4x
Notice: Large, flat printed resin parts may suffer some small curvature if exposed to high temperatures, e.g. during transport. In case of receiving a part with such a small curvature, it can be straightened again by applying a little heat with a hair dryer.
Traffic Lights 70mm printed in 3D for miniatures and Wargames
3D printed scenery set for your favorite wargame, which could be a fantastic addition to the scenery and terrains of your tabletop games. Made in 3D printing with high quality and very realistic details, which will enhance your gaming experience.
By adding these ABS-like resin bits to your board games you add a realistic touch to your games. It has been carefully designed to mimic classic elements present in many modern cities but in miniature.
Some elements in this category may require modeling glue and other modeling tools to assemble or integrate them into your game tables. This product comes unpainted and is perfect for 28-35 mm (1:58 - 1:48) miniatures.
Size: 2x standard + 4x pedestrian (70mm height)Scale: 1:58 - 1:48Content: 6x
Bicycles printed in 3D for miniatures and Wargames
3D printed scenery set for your favorite wargame, which could be a fantastic addition to the scenery and terrains of your tabletop games. Made in 3D printing with high quality and very realistic details, which will enhance your gaming experience.
By adding these ABS-like resin bits to your board games you add a realistic touch to your games. It has been carefully designed to mimic classic elements present in many modern cities but in miniature.
Some elements in this category may require modeling glue and other modeling tools to assemble or integrate them into your game tables. This product comes unpainted and is perfect for 28-35 mm (1:58 - 1:48) miniatures.
Size: 45 x 25 mmScale: 1:58 - 1:48Content: 2x
Chain Link Fences | Police Barriers printed in 3D for miniatures and Wargames
3D printed scenery set for your favorite wargame, which could be a fantastic addition to the scenery and terrains of your tabletop games. Made in 3D printing with high quality and very realistic details, which will enhance your gaming experience.
By adding these ABS-like resin bits to your board games you add a realistic touch to your games. It has been carefully designed to mimic classic elements present in many modern cities but in miniature. The central part of the metal fences can be easily broken to simulate holes and defects.
Some elements in this category may require modeling glue and other modeling tools to assemble or integrate them into your game tables. This product comes unpainted and is perfect for 28-35 mm (1:58 - 1:48) miniatures.
Size: 50x50mmScale: 1:58 - 1:48Content: 5x
Notice: Large, flat printed resin parts may suffer some small curvature if exposed to high temperatures, e.g. during transport. In case of receiving a part with such a small curvature, it can be straightened again by applying a little heat with a hair dryer.
Chain Link Fences | Police Barriers printed in 3D for miniatures and Wargames
3D printed scenery set for your favorite wargame, which could be a fantastic addition to the scenery and terrains of your tabletop games. Made in 3D printing with high quality and very realistic details, which will enhance your gaming experience.
By adding these ABS-like resin bits to your board games you add a realistic touch to your games. It has been carefully designed to mimic classic elements present in many modern cities but in miniature. The central part of the metal fences can be easily broken to simulate holes and defects.
Some elements in this category may require modeling glue and other modeling tools to assemble or integrate them into your game tables. This product comes unpainted and is perfect for 28-35 mm (1:58 - 1:48) miniatures.
Size: 50x70mmScale: 1:58 - 1:48Content: 5x
Notice: Large, flat printed resin parts may suffer some small curvature if exposed to high temperatures, e.g. during transport. In case of receiving a part with such a small curvature, it can be straightened again by applying a little heat with a hair dryer.
XPS extruded polystyrene foam | Open-Cell XPS Foam
Open-cell XPS extruded polystyrene foam, also called Styrofoam, is a lightweight, strong, durable, and less dense material than its sister closed-cell XPS foam in blue, giving it a "low memory" effect that is ideal for marking, engraving, texture transfer, scratching, and roughing. Open-Cell XPS Foam can be used to create various scenery such as hills and cliffs, game boards, different model building elements such as bricks, or even columns and large bases for dioramas. It is a lightweight and durable material that is easy to work with, making it a popular choice among amateurs and professionals.
The texture to the touch of this material is reminiscent of very fine sandpaper, so for painting, it is recommended to post-process it by applying a protective coating or surface sealer such as our Medium Decoupage. Unlike blue XPS foam, this open-cell material can be engraved with textured rollers or carved with a modeling tool for sculpting.
Open-cell extruded XPS also has great moisture resistance and works very well as a thermal insulator. This makes it an excellent choice for creating terrains, landscapes, and other modeling elements, such as buildings, bases, and bricks, as well as being ideal for making game boards, dioramas, and other craft projects.
There are several tools you can use to shape and cut it. One of the most common tools is a hot-wire cutter, which is a handheld device that heats a wire to cut through the foam. A hot knife is another tool that uses heat to cut through the foam, but it is more precise than a hot-wire cutter and is ideal for creating intricate details.
Saws and knives can also be used to cut through this material. A hand saw or jigsaw is ideal for cutting through larger pieces of foam, while a sharp utility knife or craft knife can be used to make smaller cuts and details.
When working with this material, it is essential to take safety precautions as this material can release toxic fumes when heated or sanded vigorously. It is important to wear a fume mask or work in a well-ventilated area to avoid inhaling the fumes.
Content: 200x300mm
Thickness: 10 mm
Type: Open-cell
Estimated Density: 33 kg/m³
WARNINGS:
Extruded polystyrene XPS is capable of giving off toxic fumes when heated. That heating can be achieved when hot-wire cutting, vigorously sanding, and also by application of hot glue.
This foam should never be worked in an enclosed environment or without wearing a graded fume mask. Cutting styrofoam with an electric saw will also melt and produce fumes.
Always use appropriate glue such as tuft glue or hot glue to stick styrofoam together.
Standard PVA glue or white glue will only stick this foam where they have contact with the air, where air cannot reach the glue then the glue will NOT set and remain liquid.
Dust produced when sanding or cutting styrofoams with a saw is also hazardous and should be avoided by wearing a dust mask and using appropriate ventilation and other safety measures.
The safe maximum use temperature of extruded polystyrene foam XPS is 75 degrees Celsius (167º Fahrenheit).
XPS extruded polystyrene foam | Open-Cell XPS Foam
Open-cell XPS extruded polystyrene foam, also called Styrofoam, is a lightweight, strong, durable, and less dense material than its sister closed-cell XPS foam in blue, giving it a "low memory" effect that is ideal for marking, engraving, texture transfer, scratching, and roughing. Open-Cell XPS Foam can be used to create various scenery such as hills and cliffs, game boards, different model building elements such as bricks, or even columns and large bases for dioramas. It is a lightweight and durable material that is easy to work with, making it a popular choice among amateurs and professionals.
The texture to the touch of this material is reminiscent of very fine sandpaper, so for painting, it is recommended to post-process it by applying a protective coating or surface sealer such as our Medium Decoupage. Unlike blue XPS foam, this open-cell material can be engraved with textured rollers or carved with a modeling tool for sculpting.
Open-cell extruded XPS also has great moisture resistance and works very well as a thermal insulator. This makes it an excellent choice for creating terrains, landscapes, and other modeling elements, such as buildings, bases, and bricks, as well as being ideal for making game boards, dioramas, and other craft projects.
There are several tools you can use to shape and cut it. One of the most common tools is a hot-wire cutter, which is a handheld device that heats a wire to cut through the foam. A hot knife is another tool that uses heat to cut through the foam, but it is more precise than a hot-wire cutter and is ideal for creating intricate details.
Saws and knives can also be used to cut through this material. A hand saw or jigsaw is ideal for cutting through larger pieces of foam, while a sharp utility knife or craft knife can be used to make smaller cuts and details.
When working with this material, it is essential to take safety precautions as this material can release toxic fumes when heated or sanded vigorously. It is important to wear a fume mask or work in a well-ventilated area to avoid inhaling the fumes.
Content: 200x300mm
Thickness: 6 mm
Type: Open-cell
Estimated Density: 33 kg/m³
WARNINGS:
Extruded polystyrene XPS is capable of giving off toxic fumes when heated. That heating can be achieved when hot-wire cutting, vigorously sanding, and also by application of hot glue.
This foam should never be worked in an enclosed environment or without wearing a graded fume mask. Cutting styrofoam with an electric saw will also melt and produce fumes.
Always use appropriate glue such as tuft glue or hot glue to stick styrofoam together.
Standard PVA glue or white glue will only stick this foam where they have contact with the air, where air cannot reach the glue then the glue will NOT set and remain liquid.
Dust produced when sanding or cutting styrofoams with a saw is also hazardous and should be avoided by wearing a dust mask and using appropriate ventilation and other safety measures.
The safe maximum use temperature of extruded polystyrene foam XPS is 75 degrees Celsius (167º Fahrenheit).
XPS extruded polystyrene foam | Open-Cell XPS Foam
Open-cell XPS extruded polystyrene foam, also called Styrofoam, is a lightweight, strong, durable, and less dense material than its sister closed-cell XPS foam in blue, giving it a "low memory" effect that is ideal for marking, engraving, texture transfer, scratching, and roughing. Open-Cell XPS Foam can be used to create various scenery such as hills and cliffs, game boards, different model building elements such as bricks, or even columns and large bases for dioramas. It is a lightweight and durable material that is easy to work with, making it a popular choice among amateurs and professionals.
The texture to the touch of this material is reminiscent of very fine sandpaper, so for painting, it is recommended to post-process it by applying a protective coating or surface sealer such as our Medium Decoupage. Unlike blue XPS foam, this open-cell material can be engraved with textured rollers or carved with a modeling tool for sculpting.
Open-cell extruded XPS also has great moisture resistance and works very well as a thermal insulator. This makes it an excellent choice for creating terrains, landscapes, and other modeling elements, such as buildings, bases, and bricks, as well as being ideal for making game boards, dioramas, and other craft projects.
There are several tools you can use to shape and cut it. One of the most common tools is a hot-wire cutter, which is a handheld device that heats a wire to cut through the foam. A hot knife is another tool that uses heat to cut through the foam, but it is more precise than a hot-wire cutter and is ideal for creating intricate details.
Saws and knives can also be used to cut through this material. A hand saw or jigsaw is ideal for cutting through larger pieces of foam, while a sharp utility knife or craft knife can be used to make smaller cuts and details.
When working with this material, it is essential to take safety precautions as this material can release toxic fumes when heated or sanded vigorously. It is important to wear a fume mask or work in a well-ventilated area to avoid inhaling the fumes.
Content: 200x300mm
Thickness: 20 mm
Type: Open-cell
Estimated Density: 33 kg/m³
WARNINGS:
Extruded polystyrene XPS is capable of giving off toxic fumes when heated. That heating can be achieved when hot-wire cutting, vigorously sanding, and also by application of hot glue.
This foam should never be worked in an enclosed environment or without wearing a graded fume mask. Cutting styrofoam with an electric saw will also melt and produce fumes.
Always use appropriate glue such as tuft glue or hot glue to stick styrofoam together.
Standard PVA glue or white glue will only stick this foam where they have contact with the air, where air cannot reach the glue then the glue will NOT set and remain liquid.
Dust produced when sanding or cutting styrofoams with a saw is also hazardous and should be avoided by wearing a dust mask and using appropriate ventilation and other safety measures.
The safe maximum use temperature of extruded polystyrene foam XPS is 75 degrees Celsius (167º Fahrenheit).
XPS extruded polystyrene foam | Open-Cell XPS Foam
Open-cell XPS extruded polystyrene foam, also called Styrofoam, is a lightweight, strong, durable, and less dense material than its sister closed-cell XPS foam in blue, giving it a "low memory" effect that is ideal for marking, engraving, texture transfer, scratching, and roughing. Open-Cell XPS Foam can be used to create various scenery such as hills and cliffs, game boards, different model building elements such as bricks, or even columns and large bases for dioramas. It is a lightweight and durable material that is easy to work with, making it a popular choice among amateurs and professionals.
The texture to the touch of this material is reminiscent of very fine sandpaper, so for painting, it is recommended to post-process it by applying a protective coating or surface sealer such as our Medium Decoupage. Unlike blue XPS foam, this open-cell material can be engraved with textured rollers or carved with a modeling tool for sculpting.
Open-cell extruded XPS also has great moisture resistance and works very well as a thermal insulator. This makes it an excellent choice for creating terrains, landscapes, and other modeling elements, such as buildings, bases, and bricks, as well as being ideal for making game boards, dioramas, and other craft projects.
There are several tools you can use to shape and cut it. One of the most common tools is a hot-wire cutter, which is a handheld device that heats a wire to cut through the foam. A hot knife is another tool that uses heat to cut through the foam, but it is more precise than a hot-wire cutter and is ideal for creating intricate details.
Saws and knives can also be used to cut through this material. A hand saw or jigsaw is ideal for cutting through larger pieces of foam, while a sharp utility knife or craft knife can be used to make smaller cuts and details.
When working with this material, it is essential to take safety precautions as this material can release toxic fumes when heated or sanded vigorously. It is important to wear a fume mask or work in a well-ventilated area to avoid inhaling the fumes.
Content: 200x300mm
Thickness: 30 mm
Type: Open-cell
Estimated Density: 33 kg/m³
WARNINGS:
Extruded polystyrene XPS is capable of giving off toxic fumes when heated. That heating can be achieved when hot-wire cutting, vigorously sanding, and also by application of hot glue.
This foam should never be worked in an enclosed environment or without wearing a graded fume mask. Cutting styrofoam with an electric saw will also melt and produce fumes.
Always use appropriate glue such as tuft glue or hot glue to stick styrofoam together.
Standard PVA glue or white glue will only stick this foam where they have contact with the air, where air cannot reach the glue then the glue will NOT set and remain liquid.
Dust produced when sanding or cutting styrofoams with a saw is also hazardous and should be avoided by wearing a dust mask and using appropriate ventilation and other safety measures.
The safe maximum use temperature of extruded polystyrene foam XPS is 75 degrees Celsius (167º Fahrenheit).
Closed cell XPS foam 30mm | Closed cell extruded polystyrene foam | Blue Board
Closed-cell extruded polystyrene foam XPS also called Blue Board or Styrofoam is lightweight, tough, durable, and ideal for crafting terrains such as hills and cliffs, making gaming boards, different model building elements such as bricks, and even buildings, and bases. It is a lightweight and durable material that is easy to work with, making it a popular choice among hobbyists and professionals.
Extruded XPS is a closed-cell foam, which means it has a high resistance to moisture and is a good thermal insulator. This makes it an excellent choice for creating terrains, landscapes, and other model-building elements, including buildings, bases, and bricks, as well as ideal for making gaming boards, dioramas, and other DIY projects.
There are several tools you can use to shape and cut it. One of the most common tools is a hot-wire cutter, which is a handheld device that heats a wire to cut through the foam. A hot knife is another tool that uses heat to cut through the foam, but it is more precise than a hot-wire cutter and is ideal for creating intricate details.
Saws and knives can also be used to cut through this material. A hand saw or jigsaw is ideal for cutting through larger pieces of foam, while a sharp utility knife or craft knife can be used to make smaller cuts and details.
When working with this material, it is essential to take safety precautions as this material can release toxic fumes when heated or sanded vigorously. It is important to wear a fume mask or work in a well-ventilated area to avoid inhaling the fumes.
Content: 200x300x30mm
Type: closed cell blue board
Estimated Density: 36 kg/m³
WARNINGS:
Extruded polystyrene XPS is capable of giving off toxic fumes when heated. That heating can be achieved when hot-wire cutting, vigorously sanding, and also by application of hot glue.
This foam should never be worked in an enclosed environment or without wearing a graded fume mask. Cutting styrofoam with an electric saw will also melt and produce fumes.
Always use appropriate glues such as Tuft Glue or hot glue to stick styrofoam together.
Standard PVA glue or white glue will only stick this foam where they have contact with the air, where air cannot reach the glue then the glue will NOT set and remain liquid.
Dust produced when sanding or cutting styrofoams with a saw is also hazardous and should be avoided by wearing a dust mask and using appropriate ventilation and other safety measures.
The safe maximum use temperature of extruded polystyrene foam XPS is 75 degrees Celsius (167º Fahrenheit).
Infestation Set
With this selection of materials and model paints, you will be able to replicate environments infested by alien creatures. The different pigments, textures, putty, fluorescent vegetation, creatures, and xenomorph structures included in this basing set will allow you to customize your model or diorama, giving a touch of realism and originality to the scene. Perfect for beginners and hobbyists alike, these modeling and wargaming materials will help you bring your idea to life.
Contains:
Martian Textures - Fluor Red 30ml
Martian Textures - Fluor Purple 30ml
Fluor Pigments - Green Lime 30ml
Fluor Pigments - Fluor Pink 30ml
Blood Effects - Prince Tau 17ml
Blood Effects - Demon 17ml
Splash Gel - Water Effects 30ml
Dry Brush Paint - Coral touch 30ml
Islandmoss - Light Pink
Islandmoss - Violet
Martian Fluor Grass - Punkpink Neon
Martian Tufts 6mm - On Fire Purple
Green Stuff Putty 15cm (6 inches)
Resin pieces
Avatar World Set
With this selection of materials and model paints you can replicate the effects of alien environments with extravagant Martian plants and strident colors. The different pigments, textures, alien plants, fluorescent Martian vegetation, and hyper-realistic crystals included in this basing set will allow you to customize your model or diorama, giving a touch of realism and originality to the scene. Perfect for beginners and hobbyists alike these modeling and wargaming materials will help you bring your idea to life.
Contains:
Martian Textures - Fluor Purple 30ml
Martian Textures - Fluor Blue 30ml
Fluor Pigments - Light Orange 30ml
Dry Brush Paint - Ultramarine touch 30ml
Dry Brush Paint - Dry Violet 30ml
Martian Tufts 6mm - Neon Yeti Blue
Martian Tufts 6mm - Neo-Titan Orange
Martian Fluor Grass - Wildfire Green
Basing Bark Chips
Islandmoss - Fuchsia
Islandmoss - Grey
Resin pieces
The GSW Army Transport Backpack is the backpack version of our Army Transport Bag specifically designed to protect your figures during transport. It can be used on your back, or simply as a travel bag with a cross strap to carry it on your shoulder.
The GSW miniatures transport backpack is an essential accessory for wargame players and miniatures collectors. This product stands out for combining functionality, durability, and comfort, providing an optimal solution for transporting and protecting delicate miniatures during travel and relocation. The backpack is made of Oxford fabric, known for its lightness and resistance, which makes it ideal to withstand frequent use and adverse transport conditions. In addition, its padding ensures additional protection against impacts and falls, guaranteeing that the miniatures arrive in perfect condition at their destination.
With a capacity to carry more than 200 figures, this backpack is perfect for those who need to carry a large number of miniatures to tournaments, gaming sessions or exhibitions. The miniatures are distributed among four levels, allowing for efficient and accessible organization. This storage system is complemented by removable metalized trays, which make it easy to arrange and access miniatures. The MDF trays have an adhesive metal coating which provides a stable and secure base for the magnetized figures. The backpack includes four trays, as well as 21 adjustable heights, allowing the internal space to be customized according to the specific needs of each user and the size of the miniatures.
To ensure the integrity of the backpack and the safety of its contents, the GSW includes a reinforced MDF cabinet. This internal structure provides rigidity and durability, protecting the miniatures from possible crushing or deformation during transport. In addition, the GSW backpack is designed to be extremely versatile in terms of transportation. It can be used as a traditional backpack, carrying it comfortably on the back, or as a travel bag, using a crossbody strap to carry it over one shoulder.
Comfort of use is another outstanding feature of this backpack. In addition to its capacity and strength, the GSW is equipped with a long shoulder strap and a top handle, elements that are designed to provide comfortable handling. These details allow the backpack to be lifted and carried with ease, even when fully loaded. For those who need additional space, the GSW backpack offers a modification option. It is possible to remove the first lower removable tray and glue the metalized rubber directly to the base of the drawer. This process involves trimming the rubber with scissors to fit snugly into the base structure. By doing this, the lower level is no longer removable, but you gain a few extra inches of internal space, which can be crucial for carrying larger miniatures or additional accessories.
As for its dimensions, the backpack measures 45x30x18 cm, making it compact and easy to handle. Its total weight is 3.2 kg, which makes it light considering its carrying capacity and level of protection. Assembly instructions are included inside the backpack, providing detailed guidance for the correct placement and adjustment of the trays. This ensures that users can set up their backpacks efficiently and safely, making the most of the available space.
Includes:
1x Warhammer backpack
1x Complete cabinet
4x Trays +4x adhesive metallized rubber sheet
Warning: This carrying case must protect your wargame armies, so it is absolutely necessary to reinforce the assembly with PVA glue.
Mirror Spray Paint 400ml
Chrome spray paint is a specialized aerosol designed to create a reflective, mirror-like finish on various surfaces. This type of Mirror Spray Paint contains fine metallic particles suspended in a solvent-based medium, which, when applied, align to produce a shiny, chrome-like appearance. It is commonly used in automotive, decorative, and DIY projects to achieve the look of chrome plating without the associated costs and complexities.
Mirror spray paint is versatile and can be applied to various surfaces, including metal, plastic, and wood. This adaptability makes it ideal for numerous applications, ranging from automotive parts and accessories to home décor and DIY projects. However, to achieve the best results on different materials, it may be necessary to use specific preparation techniques, such as applying primers designed for the particular type of surface, whether plastic or metal.
The final appearance of the mirror spray paint will significantly depend on the color and texture of the surface being painted. To achieve a consistent and reflective finish, it is highly recommended to apply a glossy black primer before starting the painting process. This step ensures that the metallic particles in the paint align correctly, enhancing the reflective properties and providing a smoother, mirror-like finish.
The texture of the base surface also plays a crucial role in the final result, so:
A matte black base will produce a burnished metal look
A satin black base will result in a nice silver metallic finish.
For the most mirror-like effect, a glossy black base is essential. This glossy undercoat will maximize the reflective quality of the paint, creating a true mirror effect.
INSTRUCTIONS FOR USE:
- Shake the can properly before each use.- Do not apply too much paint in one spot to avoid the "eye cat effect". This type of paint should be applied with oscillations from left to right to ensure a constant and even application.- Hold the aerosol at least 20-30 centimeters away from the surface you want to paint. This will ensure that the paint is evenly distributed over the entire surface. If you have to access difficult areas, you can get close, but move the spray paint quickly to avoid build-up and drips.- Do not apply the paint from too far away to avoid a rough surface. If it is applied from too close it may drip.- Sprays have propellant gas that could damage some plastics if applied too closely.- Keep the spray at 90º during use. - Clean the diffuser after each use by spraying a little paint but with the bottle completely upside down. In this way, only gas will come out cleaning the inner tubes as well as the diffusers.
WARNINGS:
Keep out of children's reach.
Keep away from heat/sparks / open flames / hot surfaces.
Do not spray on an open flame or another source of ignition.
Do not pierce or burn, even after use.
Keep the recipient hermetically sealed.
IN CASE OF INHALATION: Remove the person to fresh air and keep in a position that facilitates breathing.
IN CASE OF CONTACT WITH THE EYES: Rinse carefully with water for several minutes. Call a POISON CENTER or doctor: If eye irritation persists, see a doctor.
Miniature window frames are meticulously crafted, scaled-down versions of real windows designed for integration into modern and fantasy dioramas as well as dollhouses. These frames play a crucial role in enhancing the realism and intricate detail of dioramas, defining the architectural style and period of the houses.
They can be installed in prefabricated or custom-made houses using clear-drying adhesives. Essential tools for painting, creating, and installing these frames include sharp cutting blades, tweezers, and fine-tipped brushes. Miniature window frames are essential for bringing small worlds to life, whether for a charming dollhouse or a detailed diorama.
Enhance the finish using them with our miniature stained glass collection, available exclusively at Green Stuff World, for a stunning and realistic touch to your creations. We recommend using PVA glue or cyanoacrylate glue for assembly and model paints for painting, as these frames are delivered unpainted.
Thickness: 2 mmSize: 150x225 mmContent: 1 set
Miniature window frames are meticulously crafted, scaled-down versions of real windows designed for integration into modern and fantasy dioramas as well as dollhouses. These frames play a crucial role in enhancing the realism and intricate detail of dioramas, defining the architectural style and period of the houses.
They can be installed in prefabricated or custom-made houses using clear-drying adhesives. Essential tools for painting, creating, and installing these frames include sharp cutting blades, tweezers, and fine-tipped brushes. Miniature window frames are essential for bringing small worlds to life, whether for a charming dollhouse or a detailed diorama.
Enhance the finish using them with our miniature stained glass collection, available exclusively at Green Stuff World, for a stunning and realistic touch to your creations. We recommend using PVA glue or cyanoacrylate glue for assembly and model paints for painting, as these frames are delivered unpainted.
Thickness: 2 mmSize: 150x225 mmContent: 1 set
Miniature window frames are meticulously crafted, scaled-down versions of real windows designed for integration into modern and fantasy dioramas as well as dollhouses. These frames play a crucial role in enhancing the realism and intricate detail of dioramas, defining the architectural style and period of the houses.
They can be installed in prefabricated or custom-made houses using clear-drying adhesives. Essential tools for painting, creating, and installing these frames include sharp cutting blades, tweezers, and fine-tipped brushes. Miniature window frames are essential for bringing small worlds to life, whether for a charming dollhouse or a detailed diorama.
Enhance the finish using them with our miniature stained glass collection, available exclusively at Green Stuff World, for a stunning and realistic touch to your creations. We recommend using PVA glue or cyanoacrylate glue for assembly and model paints for painting, as these frames are delivered unpainted.
Thickness: 2 mmSize: 150x225 mmContent: 1 set
Miniature window frames are meticulously crafted, scaled-down versions of real windows designed for integration into modern and fantasy dioramas as well as dollhouses. These frames play a crucial role in enhancing the realism and intricate detail of dioramas, defining the architectural style and period of the houses.
They can be installed in prefabricated or custom-made houses using clear-drying adhesives. Essential tools for painting, creating, and installing these frames include sharp cutting blades, tweezers, and fine-tipped brushes. Miniature window frames are essential for bringing small worlds to life, whether for a charming dollhouse or a detailed diorama.
Enhance the finish using them with our miniature stained glass collection, available exclusively at Green Stuff World, for a stunning and realistic touch to your creations. We recommend using PVA glue or cyanoacrylate glue for assembly and model paints for painting, as these frames are delivered unpainted.
Thickness: 2 mmSize: 150x225 mmContent: 1 set
Miniature window frames are meticulously crafted, scaled-down versions of real windows designed for integration into modern and fantasy dioramas as well as dollhouses. These frames play a crucial role in enhancing the realism and intricate detail of dioramas, defining the architectural style and period of the houses.
They can be installed in prefabricated or custom-made houses using clear-drying adhesives. Essential tools for painting, creating, and installing these frames include sharp cutting blades, tweezers, and fine-tipped brushes. Miniature window frames are essential for bringing small worlds to life, whether for a charming dollhouse or a detailed diorama.
Enhance the finish using them with our miniature stained glass collection, available exclusively at Green Stuff World, for a stunning and realistic touch to your creations. We recommend using PVA glue or cyanoacrylate glue for assembly and model paints for painting, as these frames are delivered unpainted.
Thickness: 2 mmSize: 150x225 mmContent: 1 set
Miniature window frames are meticulously crafted, scaled-down versions of real windows designed for integration into modern and fantasy dioramas as well as dollhouses. These frames play a crucial role in enhancing the realism and intricate detail of dioramas, defining the architectural style and period of the houses.
They can be installed in prefabricated or custom-made houses using clear-drying adhesives. Essential tools for painting, creating, and installing these frames include sharp cutting blades, tweezers, and fine-tipped brushes. Miniature window frames are essential for bringing small worlds to life, whether for a charming dollhouse or a detailed diorama.
Enhance the finish using them with our miniature stained glass collection, available exclusively at Green Stuff World, for a stunning and realistic touch to your creations. We recommend using PVA glue or cyanoacrylate glue for assembly and model paints for painting, as these frames are delivered unpainted.
Thickness: 2 mmSize: 150x225 mmContent: 1 set
Miniature window frames are meticulously crafted, scaled-down versions of real windows designed for integration into modern and fantasy dioramas as well as dollhouses. These frames play a crucial role in enhancing the realism and intricate detail of dioramas, defining the architectural style and period of the houses.
They can be installed in prefabricated or custom-made houses using clear-drying adhesives. Essential tools for painting, creating, and installing these frames include sharp cutting blades, tweezers, and fine-tipped brushes. Miniature window frames are essential for bringing small worlds to life, whether for a charming dollhouse or a detailed diorama.
Enhance the finish using them with our miniature stained glass collection, available exclusively at Green Stuff World, for a stunning and realistic touch to your creations. We recommend using PVA glue or cyanoacrylate glue for assembly and model paints for painting, as these frames are delivered unpainted.
Thickness: 2 mmSize: 150x225 mmContent: 1 set
Miniature window frames are meticulously crafted, scaled-down versions of real windows designed for integration into modern and fantasy dioramas as well as dollhouses. These frames play a crucial role in enhancing the realism and intricate detail of dioramas, defining the architectural style and period of the houses.
They can be installed in prefabricated or custom-made houses using clear-drying adhesives. Essential tools for painting, creating, and installing these frames include sharp cutting blades, tweezers, and fine-tipped brushes. Miniature window frames are essential for bringing small worlds to life, whether for a charming dollhouse or a detailed diorama.
Enhance the finish using them with our miniature stained glass collection, available exclusively at Green Stuff World, for a stunning and realistic touch to your creations. We recommend using PVA glue or cyanoacrylate glue for assembly and model paints for painting, as these frames are delivered unpainted.
Thickness: 2 mmSize: 150x225 mmContent: 1 set
Miniature window frames are meticulously crafted, scaled-down versions of real windows designed for integration into modern and fantasy dioramas as well as dollhouses. These frames play a crucial role in enhancing the realism and intricate detail of dioramas, defining the architectural style and period of the houses.
They can be installed in prefabricated or custom-made houses using clear-drying adhesives. Essential tools for painting, creating, and installing these frames include sharp cutting blades, tweezers, and fine-tipped brushes. Miniature window frames are essential for bringing small worlds to life, whether for a charming dollhouse or a detailed diorama.
Enhance the finish using them with our miniature stained glass collection, available exclusively at Green Stuff World, for a stunning and realistic touch to your creations. We recommend using PVA glue or cyanoacrylate glue for assembly and model paints for painting, as these frames are delivered unpainted.
Thickness: 2 mmSize: 150x225 mmContent: 1 set
Miniature window frames are meticulously crafted, scaled-down versions of real windows designed for integration into modern and fantasy dioramas as well as dollhouses. These frames play a crucial role in enhancing the realism and intricate detail of dioramas, defining the architectural style and period of the houses.
They can be installed in prefabricated or custom-made houses using clear-drying adhesives. Essential tools for painting, creating, and installing these frames include sharp cutting blades, tweezers, and fine-tipped brushes. Miniature window frames are essential for bringing small worlds to life, whether for a charming dollhouse or a detailed diorama.
Enhance the finish using them with our miniature stained glass collection, available exclusively at Green Stuff World, for a stunning and realistic touch to your creations. We recommend using PVA glue or cyanoacrylate glue for assembly and model paints for painting, as these frames are delivered unpainted.
Thickness: 2 mmSize: 150x225 mmContent: 1 set
Stunning range of printed miniature stained glass, designed to bring vibrant and authentic touches to miniature scenes, dollhouses, dioramas, and scale models. Our printed miniature stained glass captures the essence of traditional stained glass with intricate designs and vivid colors, meticulously crafted to fit small-scale environments. These products are crafted using high-quality transparent plastic sheets, which serve as the perfect canvas for detailed and vibrant designs, ensuring each piece boasts sharp, clear patterns and brilliant colors that mimic the beauty and intricacy of full-sized stained glass windows.
The main feature of Green Stuff World’s miniature stained glass is our innovative double-printing system. This unique method ensures that the designs remain visible and striking, even without backlighting. Whether your model is displayed in a well-lit area or a darker setting, it retains its beauty and clarity. This double printing system also makes our product ideal for use on black backgrounds, where traditional transparent stained glass effects might be lost. This innovation ensures that even in less-than-ideal lighting conditions, its visual impact enhances the overall aesthetic of your project.
The interplay of light and color through them creates a dynamic and captivating visual effect, adding depth and realism to projects. Whether you’re a hobbyist, model builder, or collector, our miniature stained glass enhances the aesthetic quality of your work, providing a professional and polished look.
Enhance your creations with a stunning and realistic touch using also our exclusive miniature windows collection, available only at Green Stuff World. For assembly, we recommend using PVA glue or cyanoacrylate glue.
Thickness: 0.3 mmSize: 150x220 mmScale: 1/48 - 1/35Content: 1 set
Stunning range of printed miniature stained glass, designed to bring vibrant and authentic touches to miniature scenes, dollhouses, dioramas, and scale models. Our printed miniature stained glass captures the essence of traditional stained glass with intricate designs and vivid colors, meticulously crafted to fit small-scale environments. These products are crafted using high-quality transparent plastic sheets, which serve as the perfect canvas for detailed and vibrant designs, ensuring each piece boasts sharp, clear patterns and brilliant colors that mimic the beauty and intricacy of full-sized stained glass windows.
The main feature of Green Stuff World’s miniature stained glass is our innovative double-printing system. This unique method ensures that the designs remain visible and striking, even without backlighting. Whether your model is displayed in a well-lit area or a darker setting, it retains its beauty and clarity. This double printing system also makes our product ideal for use on black backgrounds, where traditional transparent stained glass effects might be lost. This innovation ensures that even in less-than-ideal lighting conditions, its visual impact enhances the overall aesthetic of your project.
The interplay of light and color through them creates a dynamic and captivating visual effect, adding depth and realism to projects. Whether you’re a hobbyist, model builder, or collector, our miniature stained glass enhances the aesthetic quality of your work, providing a professional and polished look.
Enhance your creations with a stunning and realistic touch using also our exclusive miniature windows collection, available only at Green Stuff World. For assembly, we recommend using PVA glue or cyanoacrylate glue.
Thickness: 0.3 mmSize: 150x220 mmScale: 1/48 - 1/35Content: 1 set
Stunning range of printed miniature stained glass, designed to bring vibrant and authentic touches to miniature scenes, dollhouses, dioramas, and scale models. Our printed miniature stained glass captures the essence of traditional stained glass with intricate designs and vivid colors, meticulously crafted to fit small-scale environments. These products are crafted using high-quality transparent plastic sheets, which serve as the perfect canvas for detailed and vibrant designs, ensuring each piece boasts sharp, clear patterns and brilliant colors that mimic the beauty and intricacy of full-sized stained glass windows.
The main feature of Green Stuff World’s miniature stained glass is our innovative double-printing system. This unique method ensures that the designs remain visible and striking, even without backlighting. Whether your model is displayed in a well-lit area or a darker setting, it retains its beauty and clarity. This double printing system also makes our product ideal for use on black backgrounds, where traditional transparent stained glass effects might be lost. This innovation ensures that even in less-than-ideal lighting conditions, its visual impact enhances the overall aesthetic of your project.
The interplay of light and color through them creates a dynamic and captivating visual effect, adding depth and realism to projects. Whether you’re a hobbyist, model builder, or collector, our miniature stained glass enhances the aesthetic quality of your work, providing a professional and polished look.
Enhance your creations with a stunning and realistic touch using also our exclusive miniature windows collection, available only at Green Stuff World. For assembly, we recommend using PVA glue or cyanoacrylate glue.
Thickness: 0.3 mmSize: 150x220 mmScale: 1/48 - 1/35Content: 1 set
